shrinkages
英
美
(shrinkage 的复数) n. 收缩, 收缩量, 减低
[化] 起皱; 收缩; 收缩量
shrinkage的复数
双语例句
- The strength of popular cement at 3d and 28d be equivalent to high C3S cement only when it had high specific surface area, but its drying shrinkages was more than that of high C3S cement at the same curing and drying condition.
普通水泥只有在很高的比表面积时，3d和28d强度才和高C3S水泥相当，但其干缩比高C3S水泥大得多。 - When the magnesium alloys are welded by TIG or MIG, the metal in the seam will be oxidized acutely. Some defects such as cracks, voids and shrinkages appear.
当镁合金采用钨极氩弧焊、熔化极气体保护焊等焊接方法时，焊缝金属会剧烈氧化，产生气孔、裂纹等缺陷。 - Influence of Ram Extrusion of PTFE Product Properties and Shrinkages
聚四氯乙烯柱塞挤出工艺对制品性能及收缩率的影响 - The shrinkages of green bodies in X, Y, Z directions were measured. The results show that under the same pressure, there is no difference of shrinkage in X and Y directions, and does not change with the height.
结果表明，同一压力下，坯体X向和Y向收缩率一致，并且不同高度处的X、Y向收缩率无明显差异。 - The result shows that there are no casting defects, such as shrinkages, blowholes, and slag inclusions and the quality of casting is steady.
生产结果表明，铸件没有气孔、夹砂、夹渣、收缩等铸造缺陷，铸件品质稳定。 - On the basis of temperature field numeric emulating and combining with dynamic dividing technology of melting pool isolated region, this article used G/ r~ ( 1/ 2) method to predict possible shrinkages and dispersed shrinkages that may appear in solidification process.
在一般铸件温度场数值模拟的基础上，采用G/R~（1/2）法并结合熔池孤立域的动态划分技术对凝固过程中可能出现的缩松缩孔进行了数值模拟； - The design of a vertical die casting machine rotor is most important to improve the quality of the rotor, traditional rotor castings have many shrinkages such as dispersed organization, bad compaction degree, large blowholes.
电机转子立式压铸机压铸模具的设计制造是保证电机转子品质至关重要的环节，传统工艺生产的电机转子铸件存在着组织疏松、密实度差、气孔多而大等缺陷，影响着电机的各种态势性能； - Compared with the other shrinkages of hydraulic mass concrete, temperature shrinkage is the most prominent.
在水工大体积混凝土中，温度收缩是其主要的收缩。 - On the one hand, casting shrinkages at different positions of the blade are considered as nonlinear thermo-mechanical casting deformations that are calculated with accuracy by finite element analysis.
一方面，基于叶片收缩变形位移场的有限元仿真结果，更为准确地计算铸件不同部位的收缩率； - Using simulation experiment, shrinkages of injection molding parts with different thickness are studied. Simulation experiments are performed with same parameter of process condition and fixed gate dimension and position.
采用模拟实验的方法，在相同注射工艺条件下，保持浇口尺寸和位置不变，对不同厚度制品的成型收缩率进行模拟实验研究，绘制了模拟实验曲线。